Thomas Kolb
88bf94f756
Calculate current using linear fit from measurements
2017-01-15 15:49:04 +01:00
Thomas Kolb
ba11fa287c
Current calibration of v1.1 (hopefully the final one)
2016-10-09 01:25:33 +02:00
Thomas Kolb
c11cb28558
pwm variable now contains actual timer value
...
This also causes the actual PWM value to be output over UART.
2016-10-03 16:03:15 +02:00
Thomas Kolb
9b4857df1d
Tested and improved CC mode
2016-10-03 16:03:01 +02:00
Thomas Kolb
958d82b414
Calibrate parameters for v1.1
2016-10-03 16:02:41 +02:00
Thomas Kolb
f698413f8d
ADC: adapt to new libopencm3 + added calibration
2016-10-02 23:43:44 +02:00
Thomas Kolb
98c029ca6f
Constant Voltage tuning
2016-09-04 14:37:08 +02:00
Thomas Kolb
f909f26ea7
Implemented load management
2016-09-03 16:57:33 +02:00
Thomas Kolb
8ed36f6770
Some MPP tuning
2016-09-03 16:02:34 +02:00
Thomas Kolb
11d0878864
Reset PWM limit to maximum when reaching minimum
2016-08-22 21:09:41 +02:00
Thomas Kolb
a17313246d
Fixed mppMaxPWM limits
2016-08-21 19:45:05 +02:00
Thomas Kolb
6fc5a0e2c9
Some parameter tuning
2016-08-21 19:06:20 +02:00
Thomas Kolb
9e353c3248
Limit max. PWM value in MPP if power is lost too often
2016-08-21 19:05:54 +02:00
Thomas Kolb
56b44e8d1e
Replaced exponential avg. by block-average for MPP measurement
2016-08-21 19:04:22 +02:00
Thomas Kolb
0e59b70465
Show averaged values in UART output
2016-08-21 19:02:58 +02:00
Thomas Kolb
9dc1ab928c
New approach to MPP tracking
...
Test multiple points for PWM, switch to the one which gives the most
power, repeat. If two consecutive tests give the same point, hold that
for some time or until power changes too much.
2016-08-18 22:05:18 +02:00
Thomas Kolb
473253f5ab
Some MPPT tweaks (not final yet)
2016-08-17 22:05:01 +02:00
Thomas Kolb
c93c3d41fb
Code cleanup
2016-08-17 22:04:04 +02:00
Thomas Kolb
dac3d34691
State transition tuning
2016-08-14 22:46:12 +02:00
Thomas Kolb
2246ac0290
Print log data over UART
2016-08-14 04:17:06 +02:00
Thomas Kolb
71c7cb57be
Deep sleep cosmetics
2016-08-14 03:10:01 +02:00
Thomas Kolb
d313860804
Enable RTC and deep sleep (stop mode)
2016-08-14 01:38:19 +02:00
Thomas Kolb
6fc7e27c0b
State tuning; safer startup
...
- Added some initial values for variables
- Prevent too fast state switching to bootstrap (only bootstrap 5
seconds after state change)
- Made threshold voltage for switching from MPP to CV different from CV
constant voltage
2016-08-13 01:12:33 +02:00
Thomas Kolb
df0db26122
Increased target voltage
2016-08-07 16:02:51 +02:00
Thomas Kolb
cfcbbe5269
Tuning, use idle state, some power saving
2016-08-07 01:04:24 +02:00
Thomas Kolb
33dea2e7a4
First implementation of MPP tracking
2016-08-07 00:36:15 +02:00
Thomas Kolb
97db9c24db
Implemented Constant Current mode
2016-08-06 22:22:21 +02:00
Thomas Kolb
3ef6872e03
Implemented constant voltage regulator
2016-08-06 03:15:27 +02:00
Thomas Kolb
7b02652cad
Implemented bootstrap and switching
2016-08-06 01:27:11 +02:00
Thomas Kolb
809ed13e46
Cleaned up old comments
2016-08-05 20:48:54 +02:00
Thomas Kolb
e485e23038
Enabled TIM1 for PWM
2016-08-05 20:48:36 +02:00
Thomas Kolb
99447b3454
Set all output GPIOs to output
...
No final setup yet for SW_ON and BOOTSTRAP_PULSE. These are currently
just low (== off) after power-on.
2016-08-05 00:27:40 +02:00
Thomas Kolb
c56e00a084
Moved LCD control code to separate module
2016-08-05 00:06:11 +02:00
Thomas Kolb
0d98607a0a
Added calibrated current scale
2016-08-04 23:17:25 +02:00
Thomas Kolb
1b81f70df3
Initial commit
...
What already works:
- ADC-reading with DMA
- Display
- UART debugging
2016-07-28 02:14:03 +02:00
Thomas Kolb