hamnet70/doc/hamnet70.adoc

= Hamnet70: IP-based networking in the 70 cm amateur radio band
Thomas Kolb DL5TKL
0.1, 2024-04-25
:toc:

== Introduction

== General Notes

All data is transmitted in network byte order (big endian = MSB first).

== Layer 1: Physical Layer

The Physical Layer (PHY) is responsible for encoding a Layer 2 packet such that
it can be transmitted over the air. Therefore, it encodes and modulates the
data, and adds a fixed preamble to aid synchronization to the signal.
Additionally, a mechanism is defined that allows to group packets in a „burst“,
which reduces overhead.

[#phy_packet_format]
=== PHY Packet Format

A packet encoded by the PHY consists of the following blocks:

. Preamble: a fixed symbol sequence that the receiver can use to determine the start time, frequency and phase offset of the following data.
. PHY header: contains information about the packet length and modulation/coding scheme.
. Data symbols: encoded and modulated data.

==== Preamble

The preamble is a fixed 63-bit sequence generated from a linear feedback shift register with 6 bits and the generator polynomial stem:[x^6 + x^5 + 1].

The generated sequence is: `111000101111001010001100001000001111110101011001101110110100100`.

This sequence is modulated using BPSK.

The preamble is prefixed to each transmitted packet, even inside a burst.

==== PHY Header

The PHY header describes how the following data symbols should be interpreted. It consists of the following fields:

. Modulation/code combination ID (MODCOD): 4 bit
. Number of data symbols: 12 bit
. CRC16 of the raw layer 2 packet data: 16 bit
. CRC8 of the previous 32 header bits: 8 bit

Therefore the PHY header has as size of 40 bit, including CRC.

For additional protection, the header in encoded using a [8,4] Hamming code, which can reliably correct single-bit errors and detect double-bit errors in every block of four bits.

The encoded data is always modulated using QPSK.

===== Modulation/code combinations

The following table lists all supported combinations of modulation and forward error correction.

[options="header"]
.Supported modulation/code combinations
|===
| ID (binary) | Modulation | Channel Code

| 0000
| 16-QAM
| Punctured convolutional code: stem:[r=3/4], stem:[K=7]

| 0001
| QPSK
| Punctured convolutional code: stem:[r=3/4], stem:[K=7]

| _others_
| _reserved_
| _reserved_
|===

==== Data Whitening

The IP packets transferred by Hamnet70 may contain long sequences of identical bytes (think of the zeros in the middle of IPv6 addresses), which make it hard to keep the system synchronized. To prevent the transmission of many identical symbols in a row, the data is whitened using a pseudo-random sequence.

Here, a 9-bit linear feedback shift register (LFSR) according to the CCITT specification is used to generate the pseudo-random sequence. The generator polynomial is stem:[x^9 + x^5 + 1]. The data is whitened by XORing data bytes with the _whitening key_ generated from the LFSR.

The whitening key is generated by taking the LSB of the LFSR state, and shifting it into an 8-bit register from the right. Then the LFSR is advanced and the process is repeated. Every 8 repetitions the contents of the 8-bit register are XORed with a data byte to calculate the whitened data.

To remove the whitening, the same procedure is applied to the whitened data at the receiver side. XORing with the same sequence results in the original data.

Whitening is only applied to the layer 2 packet data, but not the PHY header.

==== Data Modulation

The first data symbol follows directly after the last symbol of the PHY header. The data is encoded and modulated using the scheme defined in the PHY header’s MODCOD field. The number of symbols resulting from the encoding and modulation process is stored in the PHY header as well.

=== Burst Transmission

Burst transmission allows the transmitter to send multiple packets in quick succession.

A burst consists of the following elements:

. Ramp-up sequence
. Pre-packet idle sequence (optional)
. One or more packets as defined in <<phy_packet_format>>
. Ramp-down sequence

The ramp-up, ramp-down and idle sequences consist of alternating +1/-1 BPSK symbols.

During ramp-up, their amplitude stem:[A_u(k)] is scaled up across stem:[L_u] symbols, following the curve stem:[A_u(k) = sin(π/2 * k / L_u)]. Ramp-down follows a similar sinusoidal for stem:[L_d] symbols: stem:[A_d(k) = cos(π/2 * k / L_d)]. The purpose of these sequences is to avoid splatter while turning on and off the transmitted signal.

During the pre-packet idle sequence, the alternating BPSK symbols are continued with constant amplitude 1.0. This sequence may help synchronizers acquire the signal better (especially the gain and timing regulation can benefit), but is not needed if they are fast enough. If and how this part is used is still to be determined.

Each packet in a burst includes a preamble. Packets are directly concatenated, i.e. after the last data symbol follows the first preamble symbol.

=== Pulse Forming

Pulse forming is applied to limit the bandwidth of the transmitted signal and to reduce inter-symbol interference at the receiver.

This system uses Root Raised Cosine (RRC) filters with a roll-off factor of stem:[alpha=0.2]. Therefore the bandwidth is 1.2 times the symbol rate.

The filter is applied to the whole symbol sequence of the burst. The same filter must be applied at the receiver to minimize inter-symbol interference.

== Layer 2: Link Layer

The Hamnet70 link layer is designed to ensure reliable communication between a central station (digipeater) and several clients, while making efficient use of the available airtime. To accomplish this, it uses several technologies, including variable-length addressing and Go-Back-N retransmission.

=== Node Addresses

Node addresses use the https://github.com/arngll/arnce-spec/blob/main/n6drc-arnce.md#introduction[HAM-64 address format]. This format allows to encode callsigns of up to 12 characters in a number of 16, 32, 48 or 64 bits. Additionally, it allows to replace the full version of an address with a temporary short address with only 16 bits that is used during a connection. Multicast and broadcast addresses are also specified.

=== Link Layer Header

Each layer 2 packet contains a header that identifies how the message should be interpreted. It is of variable length and composed as follows:

[cols="2,1,5", options="header"]
.Link layer header layout
|===
| Field | Length | Description

| Message type
| 3 bit
| The type of the message. See below for a list of values.

| TX request
| 1 bit
| After this message, the burst ends and the destination may transmit.

| Source address length
| 2 bit
| Length of the source address.

| Destination address length
| 2 bit
| Length of the destination address.

| TX sequence number
| 4 bit
| Sequence number of the currently transmitted packet.

| RX sequence number
| 4 bit
| Sequence number of the packet expected next.

| Source address
| 16, 32, 48 or 64 bit
| HAM-64 address identifying the sending station.

| Destination address length
| 16, 32, 48 or 64 bit
| HAM-64 address identifying the target station.
|===

The total Link Layer Header length is therefore at least 6 byte and at most 18 byte.

[cols="1,2,5", options="header"]
.Message types
|===
| Value | Name | Description

| `000`
| Data frame
| A regular data packet.

| `100`
| Connection management
| Includes functions such as establishing (or denying) new connections or closing open connections.

| _other_
| _reserved_
| All values not explicitly listed are reserved and shall be ignored by receivers.

|===

The length of the source and destination addresses is encoded as follows: `00` = 16 bit, `01` = 32 bit, `10` = 48 bit, `11` = 64 bit.

=== Ideas

To be defined:
- connection establishment procedure (request, response)
- when are new clients allowed to connect?
- handling of packets from unknown clients that are not connection requests
- signal quality handling
- go-back-N algorithm (maybe dynamic burst length depending on previous packet loss?)

== Higher Layer Protocols

[appendix]
== Modulation Details

=== BPSK

In binary phase shift keying, a `1` bit is sent as -1.0 and a `0` bit is sent as +1.0.

=== QPSK

tbd.

=== 16-QAM

tbd.